Product ID:ZYTEL 70G33HRL YLB192
MSDS Date:02/25/1993
FSC:9330
NIIN:00N046512
MSDS Number: BTMWJ

E I DU PONT DE NEMOURS & CO

1007 MARKET ST
WILMINGTON, DE 19898
US

Emergency Phone: 800-441-3637;800-424-9300(CHEMTREC)

Info Phone: 800-441-7515

Preparer: D. L. LICZWEK

Cage: B0589

E I DU PONT DE NEMOURS & CO

BRUSSEL, DE 19898 BE

Telephone: 32-(0)15-401.505

Cage: B0589

POLYHEXAMETHYLENE ADAPIMIDE

CAS: 32131-17-2

Fraction By Weight: > 65%

OSHA PEL N/K

ACGIH TLV: N/K

FIBROUS GLASS; (SHORT GLASS FIBERS)

CAS: 65997-17-3

Fraction By Weight: < 35%

OSHA PEL N/K

ACGIH TLV: N/K

MIXTURE CONTAINING INGREDIENTS 4,5, & 6

RTECS: 9999999ZZ

Fraction By Weight: < 4%

COLORANT

OSHA PEL N/K

ACGIH TLV: N/K

STABILIZERS

OSHA PEL N/K

ACGIH TLV: N/K

LUBRICANTS

OSHA PEL N/K

ACGIH TLV: N/K

NOT KNOWN, OR ANY OTHER CIRCUMSTANCE WHERE AIR

RTECS: 9999999ZZ

APPROVED FULL FACE MASK RESPIRATOR PROVIDES

RTECS: 9999999ZZ

MUST BE IN ACCORDANCE WITH APPLICABLE FEDERAL,

RTECS: 9999999ZZ

LD50 LC50 Mixture:NONE SPECIFIED BY MANUFACTURER.
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: INGEST: NO DATA ARE AVAIL.
INGEST IS NOT A PROBABLE ROUTE OF EXPOSURE. BASED ON SIMILARITY TO
OTHER POLYMERS, THE PRODUCTS LISTED ON THE MSDS ARE PREDICTED TO
HAVE LOW ORAL TOXICITY. SKIN: IN S TUDIES ON RABBITS, NYLON 66
COPOLYMERS WERE NOT SKIN IRRITANTS. MOLTEN POLYMER CAUSES THERMAL
BURNS. (EFTS OF OVEREXP)
Explanation of Carcinogenicity:NOT RELEVANT
Effects of Overexposure:HLTH HAZ: EYE: IN STUDIES ON RABBITS, NYLON 66
COPOLYMERS WERE FOUND TO BE TRANSIENT, MODERATE EYE IRRITANT.
CHRONIC: NONE KNOWN.
Medical Cond Aggravated by Exposure:NONE KNOWN.

First Aid:INHAL:CONSULT MD IF NEC. IF EXPOSURE TO FUMES FROM
OVERHEATING/COMBUST, MOVE TO FRESH AIR. CONSULT MD IF SYMPTOMS
PERSIST. SKIN: THE CMPND IS NOT LIKELY TO BE HAZ BY SKIN CNTCT, BUT
CLEANSING SKIN AFT ER USE IS ADVISABLE. IF MOLTEN POLYMER GETS ON
SKIN, COOL RAPIDLY W/COLD WATER. DO NOT ATTEMPT TO PEEL POLYMER
FROM SKIN. OBTAIN MED TREATMENT FOR THERMAL BURN. EYE:IMMED FLUSH
W/PLENTY (SUPP DATA)

Flash Point:752F,400C
Extinguishing Media:WATER, FOAM, DRY CHEMICAL, CO2.
Fire Fighting Procedures:KEEP PERSONNEL REMOVED & UPWIND OF FIRE. WEAR
NIOSH/MSHA APPROVED SCBA AND FULL PROTECTIVE EQUIPMENT .
Unusual Fire/Explosion Hazard:LARGE MOLTEN MASSES MAY IGNITE
SPONTANEOUSLY IN AIR. WATER QUENCHING OF SUCH MASSES IS GOOD
PRACTICE. HAZ GASES/VAP PRODUCED IN FIRE ARE: AMMONIA, (SUPP DATA)

Spill Release Procedures:NOTE: REVIEW FIRE & EXPLO HAZS AND SAFETY
PRECS BEFORE PROCEEDING W/CLEAN UP. USE APPROPRIATE PERSONAL
PROTECTIVE EQUIPMENT DURING CLEAN UP. SWEEP UP TO PREVENT A
SLIPPING HAZARD.
Neutralizing Agent:NONE SPECIFIED BY MANUFACTURER.

Handling and Storage Precautions:COOL, DRY PLACE. KEEP CONTAINERS
TIGHTLY CLOSED TO PREVENT MOISTURE ABSORPTION AND CONTAMINATION.
Other Precautions:NONE SPECIFIED BY MANUFACTURER.

Respiratory Protection:NIOSH/MSHA APPRVD AIR PURIFYING RESP W/AN
ORGANIC VAP CARTRIDGE & A DUST/MIST FILTER MAY BE PERMISSIBLE UNDER
CERTAIN CIRCUMSTANCES WHERE AIRBORNE CONCS ARE EXPECTED TO EXCEED
EXPOSURE LIMITS. PROT PR OVIDED BY AIR PURIFYING RESPS(SUPP DATA)
Ventilation:USE LOC EXHST TO COMPLETELY REMOVE VAPORS, FUMES, AND
PLASTICIZER LIBERATED DURING HOT PROCESSING FROM THE WORK AREA.
Protective Gloves:IMPERVIOUS GLOVES .
Eye Protection:ANSI APPRVD CHEM WORK GOGG W/FSHLD
Other Protective Equipment:IF THERE IS POTENTIAL CONTACT WITH
HOT/MOLTEN MATL, WEAR HEAT RESISTANT CLOTHING AND FOOTWEAR.
Work Hygienic Practices:NONE SPECIFIED BY MANUFACTURER.
Supplemental Safety and Health
EXPLO HAZS:CARBON MONOXIDE; SMALL AMTS OF HYDROGEN CYANIDE AND
ALDEHYDES. FIRST AID PROC: OF WATER FOR AT LEAST 15 MIN. CALL MD.
INGEST: GET MD IMMED . RESP PROT: IS LIMITED. USE NIOSH/MSHA APPR
VD POSITIVE PRESS AIR SUPPLIED RESP IF THERE IS ANY POTENTIAL FOR
AN UNCONTROLLED RELEASE, EXPOSURE LEVELS ARE (ING 7)

HCC:N1
Melt/Freeze Pt:M.P/F.P Text:>482F,>250C
Spec Gravity:1.22-1.38
Solubility in Water:INSOLUBLE
Appearance and Odor:NONE SPECIFIED BY MANUFACTURER.
Percent Volatiles by Volume:1

Stability Indicator/Materials to Avoid:YES
STRONG ACIDS AND OXIDIZING AGENTS.
Stability Condition to Avoid:HEATING ABOVE 340C.
Hazardous Decomposition Products:CYCLOPENTANONE, CARBON MONOXIDE,
ALDEHYDES, AND AMMONIA.

Waste Disposal Methods:PREFERRED OPTIONS FOR DISP ARE (1) RECYCLING,
(2) INCINERATION W/ENERGY RECOVERY, AND (3) LANDFILL. THE HIGH FUEL
VALUE OF THIS PROD MAKES OPTION 2 VERY DESIRABLE FOR MATL THAT
CANNOT BE RECYCLED. TRE ATMENT, STORAGE, TRANSPORTATION, & DISP(ING
9)

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.